Cherlen 6 dB   Floorstanding as in K+T 5/2015

Technical data
  • impedance: 4 Ohm
  • sensivity (2,83V/1m): 86 dB
  • size (HxWxD): 960 x 180 x 240 mm
  • frequency range (-8dB): 35 - 30000 Hz
  • crossover frequency(s): 2200 Hz
  • speaker type: bass reflex
Enlarge

The Cherlen 6 dB is a high-end 2 way bassreflex floorstanding speaker with Air Motion Transformer and 6 dB filter. The kit is delivered with the outstanding Audaphon AMT 1i and the excellent Morel TSCM 634. Cherlen has been developed by Dennis Frank and Daniel Gattig.

The filter is a 1st order frequency crossover. If you prefer a separation with second or third order we recommend Cherlen with 12/18 dB crossover..

The crossover consists of a 1st order high-pass filter (6 dB per octave slope) for the tweeter. The Woofers is connected to an 1st order low-pass filter (6 dB per octave slope).

The frequency response of this speaker is very balanced. The decay spectrum is nearly perfect. At low volume, i.e. 85 dB at 1 m, the nonlinear distortions are lower than 0.2% above 600 Hz and rises not over 0.6% at 95 dB at 1 m .

Our kit consists of

  • Audaphon AMT-1i
  • Morel TSCM 634
  • 2x Bass reflex tube HP70, 68x160 mm, black
  • Damping fleece MT Bondum 800 (30 x 50 x 2 cm)
  • 0,5x PE sealing tape, 5x2 mm, 7.5 m
  • Damping Sonofil 100 x 35 cm for 20 litres
  • Binding Post PK31, gold plated (one pair, red and black)
  • 3m Speaker cable 2x1.5 mm2, transparent
  • Pan screws 4x20 black, 8 pieces
  • Plan for DIY kit

the crossover components (right),
to be mounted on a small wooden board.
  • Audaphon MKP CAP Superior 6.8 uF / 400 Vdc
  • Mundorf baked varnish air core coil BL140, 0.68 mH/0.23 Ohm
  • Metal-oxide resistor, 10W 2.7 Ohm (red-purple-gold)
  • Metal-oxide resistor, 10W 4.7 Ohm (yellow-violet-gold)

Kit without cabinet, price per speaker   EUR 935,00 excl. VAT: € 785.71 / $ 887.86

Kit with high-end crossover

The high-end kit comes with a ClarityCap ESA capacitor of high quality. The inductance is a Mundorf copper foil coil for minimizing microphonic effects. - The current flow through the coil creates a magnetic field which sets the reel of wire in motion. This motion induces a voltage in the coil which adds itself to the signal. The stiffer the reel of wire is, the less the signal will be altered.

Kit with high-end-crossover without cabinet, price per speaker   EUR 959,00 excl. VAT: € 805.88 / $ 910.65

Impedance correction

If you want to use a valve amplifier with this speaker an impedance correction should be employed. In this case the component quality is less important; therefore, we offer only one kit (upon request higher quality components are available).


Price per impedance correction for one speaker, to be mounted on a small wooden board.     EUR 17,70 excl. VAT: € 14.87 / $ 16.81

universal PCBs

If you prefer to mount the crossover components on a universal PCB instead on wood
PCB 150x115 mm, tin plated, price per unit:   EUR 4,70 excl. VAT: € 3.95 / $ 4.46
We recommend one board per kit (2 boards per speaker pair)

Measurements Cherlen 6 dB

Grafik

Pictures Cherlen 6 dB

Grafik


Home   Klang+Ton Overview