Daedalus-TL   Floorstanding as in Hobby HiFi 5/2015

Technical data
  • impedance: 6 Ohm
  • sensivity (2,83V/1m): 90 dB
  • size (HxWxD): 1450 x 258 x 360 mm
  • frequency range (-8dB): 35 - 16000 Hz
  • crossover frequency(s): Hz
  • speaker type: transmission line

Daedalus-TL is a high transmission line floorstanding loudspeaker that employs a full range driver Visaton B200. This box has been developed by Bernd Timmermanns.

Daedalus, father of Icarus built a labyrinth for King Minios. The tall Daedalus TL floorstander contains a transmission line canal resembling a labyrinth.

The labyrinth style of the transmission line canal is similar to the Fuzzy Transmission Line in issue 2/2009 of Hobby HiFi.

The transmission line canal is quite long but still easy to build, since only rectangular boards (without mitre cuts) are required.

Drivers with a high Q at resonance are particularly suited for transmission line speakers.

To flatten the frequency response of the B200 full range driver a low pass is implemented, supplemented with absorption circuits in parallel to the B200.

As a result the frequency response on axis is quite linear for a full range driver.

An excerpt from the Hobby HiFi review

"In our listening room it became immediately clear that the Daedalus TL is not suited for a large audience: the sound is very directional resulting in a small sweet spot with optimum sound requiring precise positioning for an optimum listening position. Thatís obviously due to the large diaphragm. The strong directional properties are also evident in our lab results. Positioned correctly, however, the tall and slim loudspeakers reproduce an utterly fascinating sound. The sound is airy and easygoing, almost resembling electrostatic speakers. Tonal neutrality and balance are obviously mandatory for such a result; these criteria are measurable and may, therefore, be optimised. Nevertheless, itís always a wonderful experience when this effort is rewarded by a sound that is perfectly detached from the speakers and just floats in the room naturally. In addition to these properties, significantly due to the exceptionally low mechanical Q factor (Thiele-Small parameters), the speakers shows astonishing dynamics and power handling. The large full range diaphragm pays off: there is no substitute for diaphragm size... The explosive Latin rhythms on "Something Grand" by the Hilton Ruiz Ensemble donít expose any limitations, even at higher volumes. The electrifying beats are like continuos explosions and the bass guitar displays a range varying from slap to the lowest bass."

Our kit consists of

  • Visaton B200, 6 Ohm
  • 4x Damping fleece MT Bondum 800 (30 x 50 x 2 cm)
  • 0,5x PE sealing tape, 5x2 mm, 7.5 m
  • 2x Damping Sonofil 100 x 35 cm for 20 litres
  • Binding Post PK31, gold plated (one pair, red and black)
  • 2m Speaker cable 2x2.5 mm2, transparent
  • Pan screws 4x20 black, cross recess, 8 pieces
  • Plan for DIY kit

the crossover components (right),
to be mounted on a small wooden board.
  • ClarityCap PWA capacitor 1.2 uF / 160 Vdc
  • Audaphon MKP CAP Superior 1.5 uF / 400 Vdc
  • Mundorf, electrolytic capacitor, unetched, 47uF / 50 Vdc
  • Mundorf air core coil L50, 0.27 mH/0.67 0hm
  • Mundorf air core coil L50, 0.33 mH/0.75 0hm
  • Mundorf air core coil L50, 1.5 mH/1.85 0hm
  • 1.3 mm air core coil, 1.0 mH/0.32 Ohm
  • ceramic resistor 8.2 Ohm/20 Watt
  • Metal-oxide resistor, 5W 5.6 Ohm (green-blue-gold)
  • 2x Metal-oxide resistor, 5W 6.8 Ohm (blue-grey-gold)

Kit without cabinet, price per speaker   EUR 230,00 excl. VAT: € 193.28 / $ 222.27

Kit with high-end crossover

The high-end kit comes with ClarityCap capacitors of type PWA. The inductances are baked varnished coils for minimizing microphonic effects. - The current flow through the coil creates a magnetic field which sets the reel of wire in motion. This motion induces a voltage in the coil which adds itself to the signal. The stiffer the reel of wire is, the less the signal will be altered.

Kit with high-end-crossover without cabinet, price per speaker   EUR 271,00 excl. VAT: € 227.73 / $ 261.89

Impedance correction

If you want to use a valve amplifier with this speaker an impedance correction should be employed. In this case the component quality is less important; therefore, we offer only one kit (upon request higher quality components are available).


Price per impedance correction for one speaker, to be mounted on a small wooden board.     EUR 4,60 excl. VAT: € 3.87 / $ 4.45

universal PCBs

If you prefer to mount the crossover components on a 240 x 165 mm universal PCB instead on wood:
Universal PCB RA240, order no.. I-2767, price per unit:   EUR 7,60 excl. VAT: € 6.39 / $ 7.34
We recommend one board per kit (two boards for a speaker pair)


Home   Hobby HiFi Overview